The Studio Model Beveling Machine (SB-810) can bevel pieces of glass up to fourteen inches in length (a piece of glass that can be held comfortably in your hands). Two people can work on the machine at one time, producing a total of two linear inches per minute. The extremely flexible Studio Model Beveling Machine lets you handle everything from straight-line bevels to the tightest of inside curves. You can produce brilliant cutwork, surface notching, honeycomb work and mitering. Create custom jewels or glass sculptures. Edge pieces of thick glass to fit into came. Do your own cutoffs. This versatile machine is a great addition to any professional glass studio.

FEATURES

The Studio Model Beveling Machine runs on a powerful 115 volt, one-third horsepower motor (variable speed optional). The one-inch stainless steel shaft is set in the finest quality lifetime-lubricated roller bearings. Comes fully plumbed with knife-edge sprayers, standard hose connector and drain hose. The splash tray is ruggedly constructed of high impact molded polymer. The Studio Beveler can be set on your worktable or purchased with an optional stand. Built to accommodate four vertical wheels (one for each stage of the beveling process). The 8" (20cm) wheels are primarily used for straight lines and outside curves while the 4" (10cm) wheels are recommended for tight inside curves. The SB-810 is offered as a base machine void of wheels, or pick one of our complete set ups in either electroplated or bonded diamond versions. Foreign voltages are available; please specify your requirements when ordering.

Dimensions		Specifications
  36" (91cm)- Length	          Motor: 1/3 h.p.
  24" (61cm)- Width	          Voltage: 115V/230V, Single Phase
  19" (48cm)- Height	          Amperage: 3 amps
		          Speed: 600 RPM
		          Hertz: 50/60

Standard Electroplated version. Setup includes the base machine with the following wheels:

one 8" x 1-1/2" (20cm x 4cm) 120 mesh electroplated diamond
one 4" x 1-1/2" (10cm x 4cm) 120 mesh electroplated diamond
one 8" x 2" (20cm x 5cm) stone wheel
one 4" x 2" (10cm x 5cm) stone wheel
one 10" x 2" (25cm x 5cm) fiber wheel
one 6" x 2" (15cm x 5cm) fiber wheel
one 10" x 2" (25cm x 5cm) felt wheel.

Standard Bonded version. Setup includes the base machine with the following wheels:

one 8" x 1-1/2" (20cm x 4cm) 100 mesh bonded diamond
one 4" x 1-1/2" (10cm x 4cm) 100 mesh bonded diamond
one 8" x 2" (20cm x 5cm) stone wheel
one 4" x  2" 10cm x 5cm) stone wheel
one 10" x 2" (25cm x 5cm) fiber wheel
one 6" x 2" (15cm x 5cm) fiber wheel
one 10" x 2" (25cm x 5cm) felt wheel.

All Electroplated Diamond version. Setup includes the base machine with the following wheels:

one each of the 8" x 1-1/2" (20cm x 4cm) in electroplated diamond; 120, 360 and 600 mesh
one each of the 4" x 1-1/2" (10cm x 4cm) in electroplated diamond; 120, 360 and 600 mesh
one 10" x 2" (25cm x 5cm) felt wheel.

The SB-810 is available in foreign voltages; please specify requirements when ordering.

REPLACEMENT WHEELS

Electroplated Diamond Wheels

Use the 120 mesh wheel to shape your glass pieces, use the 360 mesh wheel to smooth them and the 600 mesh wheel to pre-polish your glass pieces before final polishing with the felt wheel and cerium oxide. The 8" (20cm) wheels are typically used to grind larger pieces, straights and outside curves while the 4" (10cm) wheels are typically used on small pieces and tight inside curves.

8" x 1-1/2" x 1" (20cm x 4cm x 2.54cm) 80 mesh 120 mesh 220 mesh 360 mesh 600 mesh 4" x 1-1/2" x 1" (10cm x 4cm x 2.54cm) 80 mesh 120 mesh 220 mesh 360 mesh 600 mesh

These wheels have a full 1/8" of diamond depth bonded to their surface. Constructed of a sintered board bonded with bronze, these wheels far out last the electroplated diamond wheels. An economical choice for the artist that is grinding many pieces per day.

8" x 1-1/2" x 1" (20cm x 4cm x 2.54cm) 100 mesh 220 mesh 600 mesh 4" x 1-1/2" x 1" (10cm x 4cm x 2.54cm) 100 mesh 220 mesh 600 mesh

These wheels are made of high quality aluminum oxide composite stone, specially manufactured to our specifications. For the second stage of beveling. Stone wheels are 220 grit.

8" x 2" x 1" (20cm x 5cm x 2.54cm) 4" x 2" x 1" (10cm x 5cm x 2.54cm)

Denver Glass Machinery's smoothing and polishing wheel is a revolutionary new glass wheel. It replaces the traditional cork wheel. The polishing compound is within the wheel. It saves the mess of charging the cork wheel with pumice and quickly removes light facets left by the stone wheel while polishing the glass in preparation for the final luster polish with the felt wheel. This fiber wheel is generally used in the third stage of beveling. Some dressing is needed. Use the pumice block in one dressing tools section.

6" x 2" x 1" (15cm x 5cm x 2.54cm) 10" x 2" x 5" (25cm x 5cm x 13cm) Uses the 5" to 1" (13cm to 2.54cm) flange set

Traditionally used in the third stage of beveling, these wheels are made of high-density cork. Pumice is applied for the prepolishing step.

10" x 2" x 1" (25cm x 5cm x 2.54cm) 6" x 1-1/2" x 1" (15cm x 4cm x 2.54cm) 6" x 1/2" x 1" (15cm x 1.27cm x 2.54cm)

Manufactured from high quality dense felt, these wheels are used in the last step of the beveling process. Charged with cerium oxide they give a high lustre polish to the glass.

10" x 2" x 1" (25cm x 5cm x 2.54cm) 6" x 1-1/2" x 1" (15cm x 4cm x 2.54cm) 6" x 1/2" x 1" (15cm x 1.27cm x 2.54cm)

Dressing Tools

Silicone Carbide Dressing Bar- 4" x 3/4" x3/4" (10cm x 1.9cm x 1.9cm) Correct performance of a diamond tool is dependent on exposed diamond crystal. When your diamond wheel or sawblade seems to be cutting slower, use this tool to re-expose the diamond crystal and improve its cutting ablity.

Abrasives

Pumice- This porous volcanic rock is the perfect choice for a pre-polish abrasive. Our high quality 0-grade pumice is free of all impurities. Used on cork wheels.

Cerium Oxide- High performance polishing powder. Polishes fast and yields consistently bright finishes with both synthetic and natural felt wheels.